Thompson's® WaterSeal® Advanced Clear Multi-Surface Waterproofer
For maximum strength multi-surface waterproofing, Thompson's® WaterSeal® Advanced Clear Multi-Surface Waterproofer works on exterior wood, concrete and brick and allows wood to gray naturally. Based on patented technology, this one-coat waterproofer provides the unique benefits of clean and treat in one day and immediate application to new pressure-treated wood.
Protection and Beauty
- Most Powerful Protection Against Water Damage Protects Your Investment.
- Long-Lasting Beading & Waterproofing.
- Beautiful Finish Allows Wood to Gray Naturally
- One Day Project - Applies to Both Damp or Dry Wood in just one coat.
- Waterbased: Easy, Soap & Water Clean Up.
- New Pressure Treated Wood Application: No waiting while wood can be damaged.
Actual coverage will vary considerably due to porosity of surface materials.
|Material||(approximate coverage sq. ft./gal.)|
|Smooth Concrete Block||50|
|*Clay Tile & Quarry Tile||400|
|*Slate - Masonite||400|
|Wood: Rough Sawn||125|
|Wood: Smooth Finish||225|
Directions for use
Before you begin
- Do a trial test before application. Surface may darken slightly with application and color appearance is different when fully dry. Also, previous water repellent treatments may interfere with the penetration of this product. If your deck has been routinely treated with a water-repellent, substantial cleaning may be required. To test, clean deck and apply product by brush to a one sq. ft. area that has experienced either low traffic, rests under an eave, or is in a corner. Product should penetrate wood if surface is properly cleaned.
- Do not apply if rain is expected within 48 hours. Also, temperature must be above 50° F and remain above freezing for 24 hours.
- Cover plants and shrubs. If using a sprayer, move all objects that could come in contact with over-spray. Wet over-spray can be removed by flushing immediately with water. Dry over-spray can be removed with mineral spirits, paint thinner, or alternative paint remover products, following manufacturer's safety recommendations.
- Do not use in below grade application where water pressure is a problem or on painted or recently stained surfaces.
- DO NOT USE AS AN ADDITIVE TO PAINT.
- Protect product from freezing. Do not store below 32° F. In case of accidental freezing, call The Thompson's Help Line at 1-800-367-6297.
- Surfaces and substrates must be free of all dirt, mildew, mold, waterproofers, wood stains, paint and other contaminants. Prior to application, surfaces must be thoroughly cleaned with a deck cleaner, a concrete cleaner and/or pressure-washer according to label directions and cautions. See chart below to select the right cleaning product.
|If you need to remove:||Use:|
|Stains from dirt, mildew, algae & fungus and there is little or no trace of a residual finish||Thompson's® Water Seal® Deck Wash or Oxy Multi-Surface Cleaner|
|Weathered waterproofers or semi-transparent stains in addition to stains from dirt, mildew, algae & fungus||Thompson's® Water Seal® Heavy Duty Deck Cleaner or Wood Cleaner Concentrate|
|Stronger, difficult to remove waterproofers & stains, especially solid stains in addition to stains from dirt, mildew, algae & fungus||Thompson's® Water Seal® Maximum Strength Deck Stripper or Wood Stripper Concentrate|
|On Redwood/Cedar/Hardwoods: Tannin staining and restore lighter color of these or other high extractive wood species and/or neutralize wood after using other cleaners or strippers in addition to removing stains from dirt, mildew, algae & fungus||Thompson's® Water Seal® Deck Cleaner & Brightener or Wood Brightener Concentrate|
- Redwood, Cedar & Hardwood Cleaning Instructions: These woods have natural characteristics that require special treatment to enhance beauty and waterproofing performance. When cleaning, we recommend using a pressure-washer (water only) at 1200 psi. If this is not available, use a deck or wood cleaning product followed by a Wood Brightener to restore natural color. Wait 48 hours after application of the Brightener to apply this product.
- Power Washer: A power washer is a useful tool particularly in combination with a stronger cleaner when removing film-forming finishes or stains.
- Thoroughly rinse surface and remove all excess water. After cleaning, wait at least 2 hours before applying product. Allow longer drying time (4 hours) on overcast or cooler days below 60° F. It is not necessary for the wood surface to dry completely before application of this product.
- Always allow concrete or masonry surfaces to dry thoroughly (3 or more days) before application.
- Concrete that has a smooth, flat finish must be opened to allow for proper penetration. This should be done by using a concrete etch product. Allow concrete to dry a minimum of 72 hours after etching before applying a waterproofer.
- Concrete/stucco must be completely cured (minimum of 30 days) and dry.
- Do not mix with other waterproofing products; variations in the final appearance may result.
- Do not thin.
- Manually shake or stir contents for a minimum of 2 minutes before use.
- A small trial patch should be tried before application over the entire surface.
- Apply using a paint pad or brush. Keep the leading edge wet and distribute waterproofer evenly to help avoid lapmarks and keep the color uniform. Work from top to bottom or side to side in small areas so that the leading edge remains wet at all times during applicaion. If using a garden or pump-up sprayer, back-brushing (with paint pad or brush) will be required to even out the finish. DO NOT APPLY USING A ROLLER. Some nozzle openings of sprayers may be too small for this formula. DO NOT THIN. If clogging occurs, use paint pad or brush. If using an airless sprayer, it is recommended that tips 409, 411, and 413 be used. These tips provide adequate spray patterns while applying an appopriate amount of product to the surface being treated. These tips along with back-brushing provide proper results.
- Apply only ONE THIN even coat. A heavier, or additional coat will NOT improve performance or appearance. DO NOT APPLY TWO COATS. Avoid puddling.
- Apply by brush, roller, dipping, or sprayer. A garden "pump-up" style sprayer is the simplest method. Product will appear milky white during application, but will dry clear. If puddling of product occurs, remove within 15 minutes by redistributing to dry areas or wiping off.
- Darkening of the surface and tackiness will result if over-applied or if overnight temperature falls below 40° within 48 hours of application.
- Drying time will vary depending on surface and humidity. Allow a minimum of 12 hours before using the deck or surface.
- Clean brushes and equipment with soap and water. Dry product can be removed with mineral spirits, paint thinner, or alternative paint remover products, following manufacturer's safety recommendations.