Application Directions

• Before You Begin
  • For exterior use only.
  • For wood substrates only.
  • Allow 30 days before applying on new pressure treated lumber.
  • Be sure that both surface and air temperature are above 50°F duringapplication and for 48 hours after application. Do not apply product if rainis forecasted within 24 hours of application.
  • Perform the splash test. Sprinkle water on various sections of surface to besealed. If water absorbs and darkens color of surface within five seconds,surface is porous and considered ready to be treated. If water beads upor otherwise sits on top of surface, then surface does not need protection at this time.
  • Do not use in below-grade application where water pressure is a problemor on painted or recently stained surfaces.
  • DO NOT USE AS AN ADDITIVE TO PAINT.
• Preparation Warning
  WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
• Preparation
  Surfaces and substrates must be free of all mildew stains, dust, dirt, oil, soot, grease and other contaminants. Surfaces must be thoroughly cleaned prior to application with a deck cleaner (like those in the Thompson’s® WaterSeal® cleaner line) applied according to label directions and cautions. Remove all existing loose, flaking or peeling stain. Failure to do so will result in continued flaking and peeling. If surface is damp or wet from cleaning or weather, allow the surface to dry thoroughly (a minimum of 48 hours) before application. WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead. Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective equipment, such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
• Application
  • Do not mix with other waterproofing products; variations in the final appearance of the surface being treated may result.
  • Do not thin.
  • Shake well – intermix all cans (of the same color) to be used to assure color uniformity. Shake or mix thoroughly before and occasionally during use.
  • Color samples may vary slightly when applied to wood, based on color,texture, grain, porosity and type of wood. Final color appearance may differfrom initial application. Always apply to a small test area and let dry todetermine final color before proceeding with the entire project.
  • Apply using an exterior stain pad, brush, roller, dipping or sprayer. A garden"pump-up" style sprayer is the simplest method. If overapplied, removeexcess before it dries by redistributing to dry areas or wiping off.
  • Keep the leading edge wet and distribute stain evenly. This will help avoidlap marks and keep the color uniform.
  • Work from top to bottom or side to side in areas small enough to allow theleading edge to remain wet at all times during application. Use naturalbreaks (windows, doors) as boundaries to divide large areas into moremanageable work areas.
  • Only one coat of Thompson’s® WaterSeal® Wood Sealer is necessary. Asecond coat can be added if more color is desired. Allow the first coat todry approximately 2 hours. Second coat must be applied within 4 hours ofinitial application. Image on front shown with two coats.
  • Use only with adequate ventilation.
• Dry Time
  • Drying time will vary depending on temperature and humidity.
  • Under normal conditions, Thompson’s® WaterSeal® Solid Wood Sealer should dry to the touch within 2 hours.
• CAUTIONS
  CAUTIONS: Use only with adequate ventilation. To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying. If you experience eye watering, headaches, or dizziness, increase fresh air, or wear respiratory protection (NIOSH approved) or leave the area. Avoid contact with eyes and skin. Wash hands after using. Keep container closed when not in use. Do not transfer contents to other containers for storage. FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately. WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DO NOT TAKE INTERNALLY. KEEP OUT OF THE REACH OF CHILDREN.